Thursday, June 14, 2012

A Trash bin too pretty for trash



Cheers everybody! It's a wonderful day in the studio and I wanted to share a recent project. This is a trash bin I found at a garage sale for 5 bucks!!  For several years it sat in the garage by the door, holding huge bags of dog food for our little Pollydog. Honestly, I don't know how much I thought she was going to eat....but I bought it in 20 pound bags and I would store them in this. Anyway, every time I walked by it to go into the house, I would say  "I should paint that".  Well, I finally did~!


As you see it here, I have sanded it and am ready to put a coat of primer on it.  I have wiped it good with a tack cloth to remove any sanding dust. 

I find it easier to paint if I take it all apart. That way, I get to waste a day looking for the hinges when I am ready to put it back together. I swear I always put them in a place that would be the first place I think I would look for them, but it always turns out that, it is the ...always... the last place....   And sometimes I don't find them until after I replaced them with new hinges that will fit the indentations and holes.....not an easy task because the new hinges are not shaped the same. This is important, because if I were going to replace them from the start I would sand any indentations and fill the holes when I was prepping the piece.


You can see it does not have a back on it and I knew I wanted one. (No, I didn't just take it off...)

I was planning on bead board, but then I decided to just go with plywood. So I bought a piece of quarter inch plywood and painted the background green.  Then I put a big heart on it. I had just gotten some Copic permanent markers (thank you sister Mary for chipping in!) and I used them for the final little sprigs out the top, sides and bottom. I was so excited that it was much easier then doing them with the brush and having to have the brush loaded just right with the right consistency of paint blah blah blah..... so here is how it turned out.
Copic markers are alcohol based and "permanent"...
..water proof..
BUT NOT POLYURETHANE PROOF!! :(

I had tested it on a small patch and it looked great... but when I applied the polyurethane it started bleeding and smearing!!! Oh NO!!!!  
So I did what anyone would do. I immediately spit on paper towel and started trying to clean the lines up !  Hey, you use what is handy and all the water in my containers were full of paint water from swishing paint out of the  brushes. I couldn't let it start drying for over 30 seconds and it worked.  Whew!
  I was able to clean the lines up enough that the smearing was not noticeable, and then I retraced the lines with a paint pen.  OK, now on to the next step...

Oh, here's a tip, I would have been fine with the copic markers IF instead of brushing the Poly on, I would have first sprayed a light coat of poly on, and that would have sealed it so that I could then brush the poly on without worrying about it bleeding.  When ever I am doing black and white I do that if the paint has not dried  for several days........but I was in a hurry.... Hmmmm I vaguely remember "Haste makes waste.."



I decided on some flowers for the front, and again used the copic pens on the bottom of the flowers forpart of  the ground, but the smearing on it was fine and actually added to the blending of the earth look so no heart attack there.

 This is how the cabinet looked when I was done, and everyone was impressed that I had been able to paint the heart on the inside......when I actually painted it first, and then attached it after the fact!  The green background looks yellow but it is actually green.  My friend Jenna took these pictures in her kitchen because I stopped by her house on the way to the gallery (where I was going to drop this off) and attached the  "heart back" to the cabinet. Thank you Jenna! If you wouldn't have taken these pictures, I would not have any to post because it sold within the week~
 
 


Here's a close up of the drawer, I like to make the polka dots different sizes so I purposely make some of them larger every so often..
This picture of the handle is bad I know but you get the idea. I put together two strands of beads with wire and then wrapped colored  wire around them for the handle on the drawer.

OK, guess that is all the damage I can do for the day here, guess I will go paint!
Ta Ta for now, Carolyn 
Posted by Picasa

4 comments:

  1. Carolyn, put all your hardware in a ziplock bag and tape it on your piece in a place where you won't be painting . Then you won't be hunting for it later ! :) Cindy Catlin, Columbia, La. cindycatlin58@yahoo.com

    ReplyDelete
    Replies
    1. Great Idea~! My problem is I take the hardware off so so I can sand it down, and since I paint every surface of my project, I end up putting the hardware in a plastic bag and place it on my work table never to be seen again evidently! I am going to make a conscious effort to tape them to the piece after I sand it though, even if I think I am going to paint it the next day. Thanks for the suggestion.

      Delete
  2. This article is actually remarkable one it helps many new users that desire to read always the best stuff.
    shops.crp products

    ReplyDelete